• <dd id="ltedv"><pre id="ltedv"></pre></dd>
    <th id="ltedv"><big id="ltedv"><video id="ltedv"></video></big></th>

    <tbody id="ltedv"><pre id="ltedv"></pre></tbody>

      
      
        1. <tbody id="ltedv"><track id="ltedv"></track></tbody>

          1. <legend id="ltedv"><pre id="ltedv"></pre></legend>
              <button id="ltedv"><acronym id="ltedv"><input id="ltedv"></input></acronym></button>

                1. 中文  |  English

                  美日規65W USB TYPE-C PD快充頭

                  型號:JHD-AP065U-BC-PD05,PD 五組電壓美規電源適配器/TYPE-C口/固定插腳,UL,FCC認證

                  立即咨詢

                  產品詳情

                  型號:JHD-AP065U-BC-PD05,

                  輸出:5.0V3.0A/9.0V/3.0A/12.0V3.0A/15.0V3.0A/20V3.25A,

                  輸出功率:65W

                  安規認證:UL,FCC,PSE

                  IMG_3783.JPG

                  IMG_3785.JPG

                  1. Scope/概述
                  The data details the electrical, structural and environmental requirements of a 65W (continuous output power) PD switching power supply. Support QC2.0, QC3.0, PD2.0, PD3.0,  multiple fast charge protocols. 資料詳細描述了一款65W(連續輸出功率)PD開關電源的電氣性,結構性及環境等要求。支持QC2.0、QC3.0、PD2.0、PD3.0多種快充協議。。
                  The power supply shall meet the RoHS requirement.電源符合RoHS 要求。
                  Description/類型
                  ■SMPS Adaptor(Wall mount)/插墻式適配器  □SMPS Adaptor(Desk-top)/桌面型適配器
                  □Open Frame/開放式結構                   □SMPS Unit (With Case)/帶鋁殼型
                  □Others/其他
                  2. Input Characteristics/輸入特性
                  2.1 Input Voltage & Frequency/輸入電壓與頻率
                  The range of input voltage is from 90Vac to 264Vac single phase.
                  輸入電壓范圍:從90Vac 到264Vac, 單相輸入。
                  Item/項目 Minimum/最小 Nominal/額定值 Maximum/最大
                  Input Voltage/輸入電壓 90Vac 100Vac~240Vac 264Vac
                  Input Frequency/輸入頻率 47Hz 50Hz/60Hz 63Hz
                  2.2 Input AC Current/AC輸入電流
                  1.5A max. @ 220Vac input & max. load. /在220Vac輸入和最大負載條件下最大1.5A。
                  2.3 Inrush Current (cold start)/浪涌電流(冷啟動)
                  120A max. @ 220Vac input & max. Load. /在220Vac輸入和最大負載條件下最大120A。
                  2.4 No Load Power待機功耗
                  0.1W max. @230Vac input &No Load./在230Vac輸入待機狀態下功耗小于等于0.1W。
                  2.5 Efficiency /效率
                  81.4%(5V3A),86.6%(9V3A),87.4%(12V3A),88%(15V4A),88.0%(20V3.25A) min. @ The average efficiency of 10%,25%,50%,75%,100%.load at 115/230Vac/在 115/230Vac輸入電壓下,輸出10%, 25%,50%,75%,100%負載下的平均效率最小81.4%(5V3A),86.6%(9V3A),87.4%(12V3A),88%(15V4A),88.0%(20V3.25A)。
                  3. Output Characteristics/輸出特性
                  3.1 Static Output Characteristics <Vo & R+N>/靜態輸出特性<輸出&紋波+噪聲>
                  Output
                  /輸出 Load Condition/負載條件 Voltage Range
                  /電壓范圍 R+N
                  /紋波&噪聲 Remark
                  /備注
                   Minimum
                  Load Nominal
                  Load   
                  +5V 0A 3.0A 4.75-5.25V ≤120mV 
                  +9V 0A 3.0A 8.55-9.45V ≤150mV 
                  +12V 0A 3.0A 11.4 -12.6V ≤150mV 
                  +15V 0A 4.0A 14.25-15.75V ≤200mV 
                  +20V 0A 3.25A 19.0-21.0V ≤300mV 
                  Ripple & Noise: Measurement is done by 20MHz bandwidth oscilloscope and the output paralleled a 0.1μF ceramic capacitor and a 10μF electrolysis capacitor of low ESR and high frequency.
                  (Under 220Vac input and max. load),Block diagram as following:
                  紋波與噪聲: 測量時示波器選用20MHz帶寬限制,輸出端要并聯一顆0.1μF 的陶瓷電容和一顆10μF 的高頻低阻電解電容. (在220Vac輸入和最大負載(阻性負載)條件下).
                  3.2 Line/ Load Regulation/線性/負載調整率
                  Output
                  /輸出 Load Condition/負載條件 Load Regulation/
                  負載調整率 Line Regulation/
                  線性調整率 Remark備注  
                  +5V 0A 3.0A ±3% ±2% 
                  +9V 0A 3.0A ±3% ±2% 
                  +12V 0A 3.0A ±3% ±2% 
                  +15V 0A 4.0A ±3% ±2% 
                  +20V 0A 3.25A ±3% ±2% 
                  3.3 Turn - on Delay Time/開機延遲時間
                  3.0S max. @ 100 Vac to 240 Vac input & max. load.
                  100Vac~240Vac輸入和最大負載條件下最大3S。
                  3.4 Hold-up Time/關機保持時間
                  10mS min. @ max. load & 100Vac/60Hz input turn off at worst case.
                  在100Vac/60Hz輸入、最大負載&最差情況下關機,最小10mS。
                  20mS min. @ max. load & 240Vac/50Hz input turn off at worst case.
                  在240Vac/50Hz輸入、最大負載&最差情況下關機,最小20mS
                  3.5 Rise Time/上升時間
                  50mS max. @ max. load ./在最大負載條件下最大50mS。
                  3.6 Output Overshoot / Undershoot/輸出過沖/欠沖
                  10% max. When the power on or off/當電源開/關機時最大10%。
                  3.7 Output Load Transient Response/輸出負載瞬態響應
                  Output voltage within4.75-5.25V, 8.55-9.45V,11.4 -12.6V, 14.25-15.75V, 19.0-21.0V while the load step from 25% to 50% to 25% to max. load or 50% to 75% to 50% of max. load, R/S:0.5A/μS,frequency :100Hz,Output overshoot is less then ±5%.
                  輸出電壓在4.75-5.25V, 8.55-9.45V,11.4 -12.6V, 14.25-15.75V, 19.0-21.0V之間,負載變化: 從25%到50%再到25%或從最大負載的50%到75%再到50%,斜率:0.5A/μS,頻率: 100Hz,輸出過沖小于±5%。
                  4. Protection Requirements/保護要求
                  4.1 Short Circuit Protection/短路保護
                  The input power shall decrease when the output of short ,the power supply shall no damage , and shall be self-recovery when the fault condition is removed.
                  當輸出短路時,產品輸入功率降低且不會損傷,當短路情況解除后,產品將會自動恢復正常。
                  4.2Over Current Protection/過流保護
                  The power supply shall be in protection status when the over currents applied to the output rail, and shall be self-recovery when the fault condition is removed.
                  當過電流時,電源處于保護狀態,當過電流情況解除后,產品將會自動恢復正常。
                  輸出保護 Over Current          Protection(5V3A) Over Current     Protection(9V3A) Over Current     Protection(12V3A) Over Current     Protection(15V4A) Over Current Protection(20V3.25A) Short Circuit Protection
                  115V 輸入 ≤4.0A ≤4.0A ≤4.0A ≤4.5A ≤4.0A Hiccup
                  230V輸入 ≤4.0A ≤4.0A ≤4.0A ≤4.5A ≤4.0A Hiccup
                  5. Environment Requirements/環境要求
                  5.1 Operating Temperature and Relative Humidity/操作溫/濕度要求
                  -10℃ to +40℃/工作溫度在-10℃到 +40℃.
                  10%RH to 90%RH/濕度在10%到90%。
                  5.2 Storage Temperature and Relative Humidity/存儲溫/濕度要求
                  -20℃ to +85℃/存儲溫度在-20℃到 +85℃。       
                  5%RH to 95%RH non-condensing/濕度在5%到95%不結霜。
                  5.3 Height Above Sea Level/海拔高度
                  The power supply can normal operate at 0~5000 meter.
                  電源在海拔0~5000m能正常工作。
                  5.4 Vibration/振動
                  10 to 300Hz sweep at a constant acceleration of 1.0G(Breadth: 3.5mm) for 1 Hour for each of the perpendicular axes X, Y, Z.
                  掃描頻率: 10 to 300Hz, 加速度: 1.0G(位移: 3.5mm), X, Y, Z 三垂直坐標軸向各振動1小時。
                  6. Reliability Requirements/可靠性要求
                  6.1 Burn-in/老化
                  The power supply shall be burn-in for 8 hours at 40℃±5℃(The detail is at suggest Test Standard).
                  產品至少要在40℃±5℃的環境下老化8小時(詳見建議驗收測試標準)。
                  6.2 MTBF Qualification/平均間隔故障時間估算
                  The MTBF shall be at least 50,000hours at 40℃, max. load and nor. input condition.
                  平均間隔故障時間: 至少50,000 小時,40℃環境及額定輸入與滿載條件下。
                  6.3 跌落測試 Drop test
                  Conditions: flat marble or concrete floor; 1 m high; The bare
                  Method: 6 products, one time each,
                  Results: The product has no hidden danger and danger. Electrical performance works normally
                  條件:平面大理石或混凝土地板;高度1M;裸機
                  方式:產品6個面,各1次,
                  結果:產品無安全隱患和危險;電氣性能工作正常
                  7. EMI/EMS Standards/EMI/EMS標準
                  7.1 EMI Standards/EMI標準
                  EN55032 EN55035
                  GB13837 CISPR 22
                  GB9254 FCC Part15 Subpart B
                  7.2 EMS Standards/EMS標準
                  EN 61000-3-3 Voltage fluctuations & flicker;
                  EN 61000-4-2 Electrostatic Discharge(ESD): 8kV air discharge, 4kV contact discharge;
                  EN 61000-4-3 Radio-Frequency Electromagnetic Field Susceptibility Test-RS;
                  EN 61000-4-4 Electrical Fast Transient/Burst-FET;
                  EN 61000-4-5 Surge Immunity Test: (L-N +/-1KV,L,N-PE +/-2KV)
                  EN 61000-4-6 Conducted Radio Frequency Disturbances Test-CS;
                  EN 61000-4-8 Power Frequency Magnetic Field Test;
                  EN 1000-4-11 Voltage Dips;
                  8. Safety Standards/安規標準
                  8.1 Dielectric Strength(Hi-pot)/介電耐壓強度(高壓)
                  Primary to Secondary: 3000Vac/5mA Max/60 seconds (3.5KV/3seconds for production).
                  初級對次級: 3000Vac /5mA Max / 60秒(生產時高壓測試時間: 3.5KV/3秒)
                  8.2 Leakage Current/漏電流
                  0.25mA max. at 240Vac / 50Hz.
                  在240Vac/50Hz輸入時最大為0.25mA
                  8.3 Insulation Resistance/絕緣阻抗
                  50MΩ min. at primary to secondary add 500Vdc test voltage.
                  在初級與次級間加500Vdc 進行測試,最小50MΩ。
                  8.4 Regulatory Standards/安規標準
                  Type/安規 Country/國家 Standard/標準 State/狀況 Mark/備注
                  CCC China GB4943.1 □ IT資訊類標準
                  CE Europe EN62368-1 □ IT資訊類標準
                  cULus America/Canada UL62368-1 ■ IT資訊類標準
                  PSE Japan J62368-1 □ IT資訊類標準

                  9.Circuit Schematic Drawing/電路示意圖
                   
                  10.PCB Diagram/印刷電路板圖
                  11.Suggest Test Standard/建議驗收測試標準
                  11.1 List of Equipments/儀器設備
                  Isolated Transformer、Adjustable Transforme (0~300Vac) 、Multimeter、Oscillograph(20MHz) 、Hi-Pot Equipments、Test Load.
                  隔離變壓器、調壓器(0~300Vac)、萬用表、示波器(20MHz)、耐壓測試儀、測試負載。
                  11.2 Test Load/測試負載
                  Load 5V 9V 12V 15V 20V
                  Normal Load/額定負載 3000mA(1.66Ω) 3000mA(3.0Ω) 3000mA(4.0Ω) 4000mA(3.75Ω) 3250mA(6.15Ω)
                  Minimum Load/最小負載 0A(/Ω) 0A(/Ω) 0A(/Ω) 0A(/Ω) 0A(/Ω)
                  11.3 Test Item/測試項目
                  11.3.1 On/Off Test/開關機測試
                  1)Connect the input of power supply to AC input, and output to max. load、nor. Load、Min. load.
                  將待測電源的輸入端連接到AC輸入,輸出端接最大負載、額定負載、最小負載。
                  2)Adjust input voltage to 90Vac、220Vac、264Vac respectively, then turn on and turn off three times .If no damage ,ON/OFF test OK.
                  將調壓器分別調至90Vac、220Vac、264Vac,分別開關機三次,開關機正常。
                  11.3.2 Output Voltage Test/輸出電壓測試
                  1)Connect the input of power supply to AC input,and output to max. load、nor.Load、min. load ; test output voltage at any input voltage between 90Vac and 264Vac ,the output voltage within
                  4.75-5.25V, 8.55-9.45V,11.4 -12.6V, 14.25-15.75V, 19.0-21.0V.
                  將待測電源的輸入端連接到AC輸入,輸出端分別接最大負載、額定負載、最小負載,將輸入電壓由90Vac調至264Vac,測試輸出電壓在4.75-5.25V, 8.55-9.45V,11.4 -12.6V, 14.25-15.75V, 19.0-21.0V之間.
                  注:①在DC線末端進行電壓測試;
                  11.4 Ripple & Noise Test/紋波與噪聲測試
                  1)Test condition:Input 220Vac and output to max.load
                  測試條件:輸入電壓調節為220Vac,輸出接最大負載
                  2)Test method:Measurement is done by 20MHz bandwith oscilloscope and the output paralleled a 0.1μF ceramic capacitor and a 10μF electrolysis capacitor of low ESR and high frequency.(Under 220Vac input and max.load),Block diagram as following:
                  紋波與噪聲:測量時示波器選用20MHz帶寬限制,輸出端要并聯一顆0.1μF的陶瓷電容和一顆10μF的高頻低阻電解電容.(在220Vac輸入和最大負載(阻性負載)條件下).
                  3)Ripple & Noise Scope/各組紋波值應該在下表所示規格之內:
                  Ripple & Noise
                  紋波+噪聲 V pk-pk(5V):≤120mV V pk-pk(9V):≤150mV
                   V pk-pk(12V):≤150mV V pk-pk(15V):≤200mV
                   V pk-pk(20V):≤300mV 
                  11.5 Short Circuit Protection Test/短路測試
                  1)Test condition: input 220Vac and output max. load、nor.Load、min. load .
                  測試條件:輸出電壓調節至220Vac,輸出接最大負載、額定負載、最小負載。
                  2)The power supply shall be hiccupped when operating output in a short circuit condition and the power supply shall be self-recovering when the fault condition is removed.
                  電源處于正常工作狀態時,當輸出發生短路狀況,電源整機將處于保護狀態,短路狀況消失后自動恢復正常工作。
                  11.6 Efficiency Test/效率測試
                  81.4%(5V3A),86.6%(9V3A),87.4%(12V3A),88%(15V4A),88.0%(20V3.25A)   min. @ The average efficiency of 25%,50%,75%,100%.load at 115/230Vac/在 115/230Vac輸入電壓下,輸出25%,50%,75%,100%負載下的平均效率最小81.4%(5V3A),86.6%(9V3A),87.4%(12V3A),88%(15V4A),88.0%(20V3.25A)。
                  11.7 Hi-pot Test/耐壓測試
                  Input-output 3000Vac,60 seconds,Leakage current<5mA
                  輸入-輸出 交流3000V,60秒,漏電流<5毫安
                  11.8 Burn-in Test/老化測試
                  Adjust the input voltage to 220Vac and connect the output of the power supply to the Burn-in load,each resistant value is as following:5Vdc/3000mA(1.66ohm),9Vdc/3000mA(3.0ohm),12Vdc/3000mA(4.0ohm),15Vdc/4000mA(3.75ohm),20Vdc/3250mA(6.15ohm)the power supply can undergo a minimum of 8 hours Burn-in test at 40±5℃.
                  將輸入電壓調節為220Vac,輸出接我司老化負載:5Vdc/3000mA(1.66ohm),9Vdc/3000mA(3.0ohm),12Vdc/3000mA(4.0ohm),15Vdc/4000mA(3.75ohm),20Vdc/3250mA(6.15ohm)在40±5℃的環境下老化8小時以上,老化后再按以上步驟進行測試,電源正常工作。
                  12. Mach. Outline Drawing/外觀示意圖
                  13. Appendix I:Label/附錄一:標貼鐳雕 
                  14.Package Drawing/包裝示意圖
                  材質須符合ROHS要求,

                  服務熱線

                  0755-27335173

                  深圳市寶安區福永街道鳳凰社區興業一路6號第22棟第四、五層

                  郵箱:kevin@jhdpower.com

                  150.jpg


                  微信
                  掃一掃加關注

                  Copyright ? 版權所有 深圳市吉宏達電子有限公司 

                  高潮爽到爆的无码喷水视频_国色天香www在线观看_国产免费观看av大片的网站_最刺激的交换夫妇中文字幕